[NGUYEN KHAC BINHParticipant]

Thanks for your answer.
I want to generate the broadcast signal as shown in Picture 1 using LD Source instead of using the White light source.

Attachments:

1. 

   Picture-1.jpg
   

[NGUYEN KHAC BINHParticipant]

Hi Ahmad Atieh,
Could you tell me how to create a light source using an FP laser to transmit a signal to the FBG sensor? thank you.

[NGUYEN KHAC BINHParticipant]

I want to simulate the monitoring system using the FBGs sensor in PON. Thank you for your help.

[NGUYEN KHAC BINHParticipant]

Thank you for your reply, but I do not see the LD Source in the Optical Sources as in the attached picture. Can you help me again? thanks.

Attachments:

1. 

   Optical-sources.png
   

[NGUYEN KHAC BINHParticipant]

Hi Ahmad,

Thanks for your notice, if I have any comment on the new release, I will send to you an email.

Regards,
BINH

[NGUYEN KHAC BINHParticipant]

Thanks for your answering.

Can you explain to me about remain parameters such as Max.Q Factor, Eye Height, Threshold, and Dispersion Inst?

Regards,
Binh

[NGUYEN KHAC BINHParticipant]

Thanks for your answering.
If you know can you explain to me about the values ​contained in the attached image?
And I want to know more about Min.BER. It should is how be good? In Figure, Min.BER is 0, I think this is not real.

Attachments:

1. 

   Eye-Diagram-1.png
   

[NGUYEN KHAC BINHParticipant]

Thank you !

[NGUYEN KHAC BINHParticipant]

Thank you so much !

[NGUYEN KHAC BINHParticipant]

Hi Shaymaa
Thank you for your answer, but I want to design a simulation with a Burst Modulator at 2 Kbit/s bit rate, while the layout is 1 Gbits/s bit rate. I tried to design but I cannot it. The simulation only works when the bit rates of Layout and Burst Modulator are equal or the difference is not too large. can you help me? thanks!

Attachments:

1. 

   question_1.png
   

[NGUYEN KHAC BINHParticipant]

Hi Mohamed Abouseif,

Could you send me the file.zip again, or you can send me via nkbinh007@naver.com, thank you so much!

Binh

[NGUYEN KHAC BINHParticipant]

Hi Mohamed Abouseif,

Thank you so much! But I can not open this file, can you help me one more time, please?

Binh

Attachments:

1. 

   Untitled_4.png
   

[NGUYEN KHAC BINHParticipant]

Hi Mohamed

Thank you for your help.
I have designed a BEN with 1ns width, how to set it to 1um, can you help me, please ?

BINH

Attachments:

1. 

   Untitled_1.png
   

[NGUYEN KHAC BINHParticipant]

Hi Mohamed Abouseif

Thank you for your enthusiastic help.
I used two splitter/combiner, but the return signal does not pass the Optical Delay, do you know why?

BINH

Attachments:

1. 

   Untitled-3.png
   

[NGUYEN KHAC BINHParticipant]

Hi Mohamed Abouseif

Thank you for your replying, if using Bidirectional type then the signal after passing through Splitter Bidirectional disappears

BINH

Attachments:

1. 

   Simulation_4th_using-single.png
   

2. 

   Simulation_4th_using-Bidirectional.png
   

3. 

   ONU.png